Monster Paint Products Ltd
Toll Free (888) 766-7547
Manufacture of Marine Non-Skid Deck Paint for Fiberglass, Treated Aluminum, Concrete, and properly primed Metal and Wood Deck Substrates.
Thank you for your inquiry. Our experience has shown us that most people ask one of the following 15 questions, we know your time is valuable and we want to make sure that your question is answered as quickly as possible.
If you find that your question is not answered below, then please do not hesitate to call or email us though our Contact Us page. It is our pleasure to discuss your specific project and answer any further questions or concerns you may have.
We are not responsible for results obtained in using this product, even when used as suggested. This is because application and conditions vary, and are beyond our control. The user should conduct tests to determine the suitability of the product for the intended use. This includes liability for breach of warranty, strict liability in tort, negligence or otherwise) is limited exclusively to replacement of the product or refund of its price. Under no circumstances are we liable for incidental and consequential damages.
Non-Skid Paint comes with a 30-day money back guarantee. (See our Shipping and Returns page for complete details).
Yes, ADA recommend a minimum average Static Coefficient of Friction rating of at least 0.60 for level floors, and 0.80 for incline ramps. Non-Skid Paint far exceeds those requirements in all testing (ranging from 0.87 Dry and 0.85 Wet) Static Coefficient of Friction. See our Coefficient of Friction test results page.
Clean Non-Skid Paint with warm water mixed with any mild soap or detergent. Use a firm bristle brush and rinse off thoroughly with clean water.
It is recommended that on low to medium traffic area’s to add a topcoat once every 2-3 years. On area’s with a lot of high traffic to topcoat once every 1-2 years as needed.
Non-Skid Paint is environmentally safe to use. Easily clean hands and tools with warm soapy water immediately after application.
YES, it is recommended to use Polar White Non-Skid Paint to lighten any color of choice. For color consistency use a 1 to 2 ratio for mixing a color to achieve a lighter shade. (Example: for every 2 gallons of Shipstone Gray add 1 gallon of Polar White together in a large bucket to achieve a Light Gray Color, stir and mix thoroughly).
The Grit material in Non-Skid Paint settles to the top of can, and sometimes sticks to the lid. This is because the Grit is lighter than the Epoxy and will stay suspended and not sink to the bottom of can after thoroughly mixed. Scrap any Grit that is stuck to the lid of the container back into the paint with a wood stir-stick; so as to not losing the normal textured surface. Mix well before and during application.
NO, Non-Skid Paint is a Water Reducible Epoxy-Ester Coating and can only be thinned with water. Add no more than ½ quart of water per gallon for first coat only. (NOTE: Topcoat must be applied directly from the pail without thinning).
NO, Non-Skid Paint Epoxy is (pre-mixed) with Grit. Extra Grit Additive is recommended to increase the texture for applications such as Incline Ramps, and Stair Treads.
Coverage on most surfaces is approximately 250-350 square feet per gallon @ 4 mils wet = 1.5 mils dry (A two-coat application is required for lasting durability).
Drying time @ 77*F with 50% relative humidity.
TO THE TOUCH: 30 – 40 Minutes (tack free)
RECOAT or TOPCOAT: 1-2 Hours
DRY HARD: 72 Hours
FULL CURE: 5 – 7 Days
(Do not expose Non-Skid Paint surfaces to heavy foot traffic in less than 72 hours).
Apply when the temperature is 50*F (12*C) minimum, 90*F (32*C) maximum (air, surface and material), at least 5*F above dew point. The relative humidity should be 85% maximum. Ideal temperature is 77*F with 50% relative humidity. Also, Do not apply late in the day were dew can settle on the fresh wet paint not allowing it to dry properly. Furthermore, Do not apply if rain is threatening or in the forecast.
For Gelcoat and Fiberglass use Acetone. For Non-Ferrous Metals and Aluminum use a Industrial Degreaser and aluminum acid-etch preparation. On Concrete use Trisodium Phosphate (TSP), use a firm bristle brush and rinse off thoroughly with clean water. Area must be completely dry before application. If necessary, use a heat source such as a large Hot Air Dryer. These products are available through most Hardware Stores.
Just like normal paint! Easily apply Non Skid Paint with a brush, roller or spray can. For more details see our Product Overview page.
Non-Skid Paint is self-priming on Fiberglass, Gelcoat, Epoxy, Magnesite Decking, and Concrete surfaces. On wood substrates use a exterior oil base or latex wood primer. For metal surfaces apply an exterior metal primer over clean, dry metal, because this will also provide additional rust prevention.
Apply Non Skid Paint to well bonded, natural and painted surfaces. This includes Concrete, Magnesite Flooring, Aluminum, Metal, Fiberglass, and Wood substrates.
Do not use on garage floors or other areas where vehicles drive or park.
Also, Do not use on oil-base chemically treated wood or glossy surfaces such as porcelain or ceramic tile. * (Note: We have designed our MP1A30L Series Aerosol Spray Crystal Clear coating for porcelain tub, showers, and ceramic tile applications).
Furthermore, Do not use in areas where there is continuous standing water or where ponding occurs. Level these areas prior to use of Non-Skid Paint.
Magnesite Flooring, Stairways, Portable Classroom Ramps, Stadium Steps, Concrete Walkways, Wood Decking, Boat Decks, Swim Steps, Boat Trailers, Marina Dock Ramps, Truck Lift Gates, Trailer Approach Plate, and most pedestrian traffic areas that need a Non-Skid Surface to Help Aid in the Reduction of Slip and Fall Accidents.